 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| d a t a sh eet preliminary speci?cation supersedes data of 1996 oct 18 file under integrated circuits, ic01 1997 feb 12 integrated circuits TEA6820T; tea6822t in car entertainment (ice) car radio
1997 feb 12 2 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t features general fm mixer for conversion from fm-if 1 = 72.2 mhz to fm-if 2 = 10.7 mhz am mixer for conversion from am-if 1 = 10.7 mhz to am-if 2 = 450 khz fm-if gain stage crystal oscillator providing mixer frequencies and references for if-count and stereo decoder fm quadrature demodulator with automatic centre frequency adjustment and thd compensation level, multi-path and noise detectors soft mute stereo noise cancelling and variable de-emphasis pll stereo decoder noise blanker am if-amplifier and demodulator i 2 c-bus transceiver with interface to enable direct data transfer to radio front-end if-count for am and fm reference frequency generation for pll synthesizer. stereo decoder adjustment-free pll vco pilot depending mono/stereo switching analog control of mono/stereo blend adjacent channel noise suppression (114 khz) pilot cancelled analog control of de-emphasis integrated low-pass filters for 190 khz adjacent channel interferences and signal delay for interference absorption circuit. general description the TEA6820T together with the tea6810t and the tea6822t together with the tea6811t forms an am/fm electronic tuned car radio in a double conversion receiver concept. ordering information type number package name description version TEA6820T vso56 plastic very small outline package; 56 leads; face down sot190-2 tea6822t vso56 plastic very small outline package; 56 leads sot190-1 1997 feb 12 3 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t quick reference data note 1. ic is operating; specified parameters may deviate from limits which are valid for operating range. symbol parameter conditions min. typ. max. unit v dda1 analog supply voltage 1 (+5 v; pin 5) note 1 4.5 5.0 5.5 v operating range 4.75 5.0 5.25 v i dda1 analog supply current 1 (pin 5) fm mode 17 21 25 ma am mode 14 17 21 ma i 19 +i 20 total fm mixer output current 4.8 6.0 7.2 ma i 22 +i 23 total am mixer output current 10 12 14 ma v dda2 analog supply voltage 2 (pin 28) note 1 7.0 8.5 10 v operating range 8.1 8.5 8.9 v i dda2 analog supply current 2 (pin 28) fm mode 2.4 3.0 3.6 ma v dda3 analog supply voltage 3 (+8.5 v; pin 56) note 1 7.0 8.5 10 v operating range 8.1 8.5 8.9 v i dda3 analog supply current 3 (pin 56) fm mode 19 24 28 ma am mode 9.5 12 15 ma v ddd digital supply voltage 1 (+5 v; pin 5) note 1 4.5 5.0 5.5 v operating range 4.75 5.0 5.25 v i ddd digital supply current (pin 52) note 1 8 10 12 ma signal plus noise-to-noise ratio fm mode; d f = 22.5 khz at pins 43 and 47 66 75 - db am mode; m = 0.3 54 60 - db thd total harmonic distortion fm mode; d f=75khz - 0.1 0.35 % am mode - 1.5 3 % a cs channel separation (adjusted) 40 -- db t amb operating ambient temperature - 40 - +85 c sn + n -------------- 1997 feb 12 4 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t block diagram k , full pagewidth 100 nf 22 nf 100 nf 330 w 10 k w 10 k w 100 nf 11 sfe10.7 61.5 mhz scl sda 100 nf 100 39 40 43 48 220 nf 100 k w 33 k w 33 k w amstop 10 nf rds v ref 1.5 nf 82 k w 100 k w 220 k w 68 pf 220 nf 100 nf 2.2 m w 820 k w 12 k w 33 k w 1.2 m w 220 nf 82 k w 100 nf 470 nf leveladj v int2 v int1 29 31 100 nf 14 15 100 k w 3.3 nf 62 pf 4.3 k w 1 k w ? 2 / ? 6 54 sda scl 10 k w 330 w 330 w 17 18 v ref detector noise former pulse detector interference - + 100 100 nf 1 m w sfp450 100 k w 27 k w 22 nf 220 nf 3.3 m w mute soft 9 30 am 3 2 6 1 53 7 10 13 outleft 16 20 21 24 25 26 27 33 28 51 50 49 47 46 45 44 8 42 38 37 36 35 34 55 19 fmstop 22 23 detector average detector peak detector peak detector average switch current 60 khz pass high afc if- pass high mono matrix and decoder mpx- 38 khz 19 khz block logic canceller pilot f ref detector pilot detector phase digital vco detector phase filter low mpx multi- adc i 2 c-bus counter buffer 20 khz level adc delog am amplifier level :n5 am-amplifier fm-limiter switch am/fm reference oscillator fm am supply 56 32 41 52 outright 12 5 4 100 120 k w 100 470 nf 47 m f 47 m f v ccan 33 m f 10 w v ccdig 68 m f 6.8 nf 6.8 nf 22 m h TEA6820T tea6822t 56 pf 10 nf 9922 521 00098 or daiwa at - 49 level detector level buffer if- frequency amplifier path v ref nf i.c. - + - + amplifier pass filter v cc +8.5 v +8.5 v +5 v +5 v v ddd +5 v l13 tr5 r39 r40 r51 r41 v int1 v int2 nf nf philips 10 k w v cc1 10.7 mhz 10.7 mhz 10.7 mhz 10.7 mhz 72.2 mhz nf f ref tempera- ture compen- sation toko 7psag-1946d = s toko p392bc-1977z radio mute radio mute tuning mute mha253 fig.1 block diagram. 1997 feb 12 5 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t pinning symbol pin description qdet1 1 demodulator tank 1 qdet2 2 demodulator tank 2 tswitch 3 time switch input agnd 4 analog ground v dda1 5 analog supply voltage 1 (+5 v) hfbus1 6 hf bus 1 output; pull-up to +5 v hfbus2 7 hf bus 2 output; pull-up to +5 v xtal1 8 crystal oscillator 1 xtal2 9 crystal oscillator 2 f ref(p) 10 pll reference frequency output (p) f ref(n) 11 pll reference frequency output (n) i ref 12 reference current fmif1in1 13 72 mhz fm-if input 1 fmif1in2 14 72 mhz fm-if input 2 tsdr 15 time constant for sdr tsds 16 time constant for sds v sds 17 sds control voltage input v sdr 18 sdr control voltage input fmif2out1 19 fm mixer output 1 fmif2out2 20 fm mixer output 2 v ref 21 reference voltage output amif2out1 22 am mixer output 1 amif2out2 23 am mixer output 2 fmamdec 24 fm/am 10.7 mhz decoupling phasedet 25 phase detector output pildet 26 pilot detector output fmam10.7 27 fm/am 10.7 mhz input v dda2 28 analog supply voltage 2 fmifampout 29 fm-if ampli?er output afgnd 30 af ground deemphr 31 de-emphasis capacitor right deemphl 32 de-emphasis capacitor left amif2in1 33 am-if 2 input 1 amif2in2 34 am-if 2 input 2 fmin2 35 fm limiter input dcfeed 36 dc feed fm limiter fmin1 37 fm limiter input leveladj 38 level adjustment input c afc 39 afc capacitor mpbuf 40 multi-path buffer time constant outleft 41 af output left fmstop 42 fmstop adjustment input rds/amstop 43 mpx for rds/amstop adjustment input outright 44 af output right mpxin 45 stereo decoder mpx input i.c. 46 internally connected mpxout 47 fm demodulator mpx output amafout 48 am demodulator af output v mute/aml 49 mute voltage/am level levelunweig 50 unweighted level output iac contr 51 iac control voltage v ddd 52 digital supply voltage sda 53 serial data input/output; pull-up to +5 v scl 54 serial clock input; pull-up to +5 v dgnd 55 digital ground v dda3 56 analog supply voltage 3 (+8.5 v) symbol pin description 1997 feb 12 6 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t fig.2 pin configuration for tea6822t. handbook, halfpage tea6822t mha204 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 v dda3 dgnd scl v ddd iac contr v mute/aml sda levelunweig amafout mpxout i.c. mpxin outright rds/amstop fmstop outleft mpbuf c afc leveladj fmin1 dcfeed fmin2 amif2in2 amif2in1 deemphl deemphr afgnd fmifampout v dda2 fmam10.7 pildet phasedet fmamdec amif2out2 amif2out1 v ref fmif2out2 fmif2out1 v sdr v sds tsds tsdr fmif1in2 fmif1in1 i ref f ref(n) f ref(p) xtal2 xtal1 hfbus2 hfbus1 v dda1 agnd tswitch qdet2 qdet1 fig.3 pin configuration for TEA6820T (top view). handbook, halfpage TEA6820T mha419 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 v dda3 dgnd scl sda v ddd iac contr levelunweig v mute/aml amafout mpxout i.c. mpxin outright rds/amstop fmstop outleft mpbuf c afc leveladj fmin1 dcfeed fmin2 amif2in2 amif2in1 deemphl deemphr afgnd fmifampout qdet1 qdet2 tswitch agnd v dda1 hfbus1 hfbus2 xtal1 xtal2 f ref(p) f ref(n) i ref fmif1in1 fmif1in2 tsdr tsds v sds v sdr fmif2out1 fmif2out2 v ref amif2out1 amif2out2 fmamdec phasedet pildet fmam10.7 v dda2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 functional description stereo decoder by changing the value of the input resistor at pin 12 the mpx input can be adapted to the level of the fm demodulator output (see fig.16). a 3rd order low-pass filter (f g = 90 khz) at the mpx input provides an extra 190 khz aci suppression. an interference gate is connected at the mpx demodulator outputs. for am the vco is switched off. 1997 feb 12 7 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t limiting values in accordance with the absolute maximum rating system (iec 134). note 1. charge device model class b: equivalent to discharging a 200 pf capacitor via a 0 w series resistor. characteristics v 56-4 =v 28-4 = 8.5 v; v 5-4 =v 52-55 =5v; t amb =25 c; f mod = 1 khz; deviation = 22.5 khz; r g =50 w ; v 37-35 =10mv; with de-emphasis = 50 m s; coil quality = 15; unless otherwise speci?ed. symbol parameter conditions min. max. unit v dda1 analog supply voltage 1 (pin 5) - 0.3 +6.5 v v dda2 analog supply voltage 2 (pin 28) - 0.3 +12 v v dda3 analog supply voltage 3 (pin 56) - 0.3 +12 v v ddd digital supply voltage (pin 52) - 0.3 +6.5 v t stg storage temperature - 55 +150 c t amb operating ambient temperature - 40 +85 c v es electrostatic handling note 1 pins 8 and 9 - 100 +100 v all other pins - 300 +300 v symbol parameter conditions min. typ. max. unit current consumption i dda1 analog supply current 1 (pin 5) fm mode 17 21 25 ma am mode 14 17 21 ma i dda2 analog supply current 2 (pin 28) fm mode 2.4 3.0 3.6 ma i dda3 analog supply current 3 (pin 56) fm mode 19 24 28 ma am mode 9.5 12 15 ma i ddd digital supply current (pin 52) 8 10 12 ma i 19 +i 20 total fm mixer output current 4.8 6.0 7.2 ma i 22 +i 23 total am mixer output current am mode 10 12 14 ma fm-if path; see fig.4 v 19-20 max(p-p) maximum output voltage (peak-to-peak value) 12.0 14.0 - v i 19 ; i 20 mixer bias current 2.4 3.0 3.6 ma mixer leakage current in am position -- 2 m a i 19if2 /v 13-14if1 conversion gain 1.65 1.9 2.2 ms r i input resistance (pins 13 to 14) 5 7 - k w c i input capacitance (pins 13 to 14) - 3 4.5 pf r opt optimum generator resistance - 1.2 - k w r o output resistance (pins 19 to 20) 15 20 - k w c o output capacitance (pins 19 to 4 and pins 20 to 4) - 12 14 pf ip3 third order intermodulation 114 124 - db m v 1997 feb 12 8 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t oscillator f osc oscillator frequency - 61.5 - mhz d f osc oscillator frequency spread -- 250 hz d f osc / d t temperature dependence of oscillator frequency crystal type philips 9922 521 00098 - 30 10 - 6 - k - 1 r 1 crystal motional resistance -- 70 w c 0 crystal shunt capacitance -- 5pf fm-if 2 ampli?er v 27-24 max(rms) maximum input voltage for 1 db compression point (rms value) 80 110 - mv v 29-4 max(rms) maximum output voltage (rms value) 220 320 - mv v 29-4 /v 27-24 ampli?er gain loaded with 330 w ; see fig.5 912 15db d v 29-4 /v 27-24 gain temperature dependence - 25 c 1997 feb 12 11 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t a ttack and decay time for mute voltage i 49 charge current pin 3 connected to gnd - 3.5 -m a discharge current pin 3 connected to gnd -- 4.0 -m a charge current pin 3 connected to pin 5 - 150 -m a discharge current pin 3 connected to pin 5 -- 170 -m a d f muting activated by 60 khz fm interference v 49 <3v; v 37-35 =3mv; f mod = 60 khz pin 3 connected to gnd; v 43 /v 47 =9db - 40 - khz pin 3 connected to pin 5; v 43 /v 47 =6db - 40 - khz v 43 /v 47 maximum mute depth by 60 khz fm interference pin 3 connected to gnd - 15 - db pin 3 connected to pin 5 - 10 - db t ime constant for mono / stereo blend voltage ; note 4 i 16 charge current v 37-35 = 3 mv; pin 3 connected to gnd - 0.6 -m a discharge current v 37-35 = 3 mv; pin 3 connected to gnd -- 17 -m a charge current v 37-35 = 3 mv; pin 3 connected to pin 5 - 23 -m a discharge current v 37-35 = 3 mv; pin 3 connected to pin 5 -- 750 -m a m mono/stereo blend activated by 20 khz am interference v 16 <2v; v 37-35 =3mv; r l16 >50m w ; f mod = 20 khz; data byte 2 bit 5 = 0 pin 3 connected to gnd - 45 - % pin 3 connected to pin 5 - 45 - % data byte 2 bit 5 = 1 pin 3 connected to gnd - 55 - % pin 3 connected to pin 5 - 55 - % d f mono/stereo blend activated by 60 khz fm interference v 16 <2v; v 37-35 =3mv; r l16 >50m w ; f mod = 60 khz pin 3 connected to gnd - 50 - khz pin 3 connected to pin 5 - 50 - khz symbol parameter conditions min. typ. max. unit 1997 feb 12 12 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t t ime constant for high - cut control voltage sdr; note 5 i 15 charge current v 37-35 = 3 mv; pin 3 connected to gnd - 0.6 -m a discharge current v 37-35 = 3 mv; pin 3 connected to gnd -- 0.7 -m a charge current v 37-35 = 3 mv; pin 3 connected to pin 5 - 41 -m a discharge current v 37-35 = 3 mv; pin 3 connected to pin 5 -- 44 -m a m high-cut control activated by 20 khz am interference v 15 <2v; v 37-35 =3mv; r l15 >50m w ; f mod = 20 khz pin 3 connected to gnd - 45 - % pin 3 connected to pin 5 - 45 - % d f high-cut control activated by 60 khz fm interference v 15 <2v; v 37-35 =3mv; r l15 >50m w ; f mod = 60 khz pin 3 connected to gnd - 50 - khz pin 3 connected to pin 5 - 50 - khz m ulti - path detector f mp multi-path detector band-pass centre frequency - 20 - khz b mp band-pass bandwidth 7.0 -- khz reference voltage v 21-4 output voltage i 21 = - 1 ma 4.5 5.1 5.7 v d v 21-4 temperature dependence - 3.3 - mv/vk i 21 output current -- 1ma am-if path; see fig.14 and notes 6 and 7 v 22-23 max(p-p) maximum output voltage (peak-to-peak value) 12 15 - v i 22 , i 23 mixer bias current 5.0 6.0 7.0 ma mixer leakage current in fm position -- 2 m a i 22if2 /v 27-24if1 conversion gain 2.2 2.7 3.4 ms r 27-24 input resistance 300 330 360 w c 27-24 input capacitance - 58pf r 22-23 output resistance 10.0 20.0 - k w c 22-23 output capacitance - 510pf ip3 third order intermodulation - 137 - db m v symbol parameter conditions min. typ. max. unit 1997 feb 12 13 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t notes to the characteristics 1. for typical adjusting range see figs 10 and 13. 2. for typical curve see fig.11. 3. the static mute voltage follows the unweighted voltage level as function of fm-if 2 voltage and level adjustment voltage v 38-4 . it additionally depends on multi-path level, noise (adjacent channel interferences) and the position of tswitch (pin 3). for typical curve for mute voltage dependence see fig.12. 4. the mono/stereo blend voltage is generated as a function of fm-if 2 voltage, multi-path level, noise and position of tswitch. 5. the high-cut control voltage is generated as a function of fm-if 2 voltage, multi-path level, noise and position of tswitch. 6. f if1 = 10.7 mhz; f if2 = 450 khz for am mixer. 7. the am oscillator signal is generated by division of the 61.5 mhz crystal oscillator. two divider ratios programmable by the i 2 c-bus: divide by 6 (am-if 1 = 10.7 mhz); divide by 2 (am-if 1 = 30 mhz). 8. for typical am level curve see fig.15. 9. for am detector; f amif2 = 450 khz; f mod = 400 hz; m = 30%. am detector ; notes 8 and 9 v 48-4(rms) af output level (rms value) r l48 > 500 k w ; 100 m v v 33-34 300 mv 190 240 290 mv v 33-34(rms) sensitivity voltage (rms value) - 50 75 m v - 200 400 m v am-if 2 minimum input voltage (rms value) thd 5%; m = 0.8 -- 100 m v am-if 2 maximum input voltage (rms value) thd 5%; m = 0.8 800 -- mv r 33-34 if 2 input resistance 1.8 2.0 2.2 k w c 24-23 if 2 input capacitance - 10 15 pf r o48 output resistance 27 33 39 k w c o48 output capacitance -- 10 pf signal plus noise-to-noise ratio 54 60 - db thd total harmonic distortion m = 0.8; 300 m v v 33-34 200 mv - 1.5 3.0 % symbol parameter conditions min. typ. max. unit sn + n -------------- 26 db = sn + n -------------- 46 db = sn + n -------------- 1997 feb 12 14 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t stereo decoder characteristics input signal ( d f = 75 khz) v mpx(p-p) = 1.7 v; modulation frequency f mod = 1 khz; de-emphasis time constant t = 50 m s; nominal input resistor (pin 45) r i = 168 k w ; t amb =25 c; unless otherwise specified. symbol parameter conditions min. typ. max. unit v 44-4(rms) ; v 41-4(rms) af output voltage (rms value) 800 900 1000 mv v 44-4 ; v 41-4 dc output voltage 3.1 3.6 4.1 v i 44(max) ; i 41(max) maximum output current 150 --m a v 44-4 /v 41-4 difference of output voltage - 1 - +1 db r o44 ; r o41 output resistor -- 600 w r lmin minimum load resistor 12 -- k w a cs channel separation (adjusted) 40 -- db signal plus noise-to-noise ratio f = 20 hz to 15 khz 74 80 - db thd total harmonic distortion - 0.1 0.3 % mpx input overdrive margin thd = 1% 4 -- db carrier and harmonic suppression at the output; note 1 a 19 pilot signal f = 19 khz - 50 - db a 38 subcarrier f = 38 khz - 50 - db a 57 f = 57 khz - 50 - db a 76 f = 76 khz - 60 - db a 2 intermodulation f mod = 10 khz; f spur = 1 khz - 60 - db a 3 f mod = 13 khz; f spur = 1 khz - 58 - db a 57 traf?c radio (ari) f = 57 khz - 70 - db a 67 subsidiary communications authorization f = 67 khz 70 -- db a 114 adjacent channel frequency f = 114 khz - 80 - db a 190 f = 190 khz - 70 - db rr ripple rejection at output f r = 100 hz; v r = 100 mv eff - 30 - db mono/stereo control v i(pil) pilot threshold voltage stereo on - 24 30 mv mono on 8 20 - mv d v i(pil) switch hysteresis v ion /v ioff - 2 - db external mono/stereo control; note 2 v 17 - 0.765v 21 control voltage channel separation see fig.17 a =6db -- 110 - mv a =16db -- 40 - mv sn + n -------------- 1997 feb 12 15 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t muting functions (mute via i 2 c-bus) d v 44 , d v 41 dc offset voltage tune mute - 50 - +50 mv radio mute (in combination with tune mute) - 400 - +400 mv a mute tune mute 60 -- db radio mute (in combination with tune mute) 80 -- db high-cut control; see fig.18 v 18 - 0.765v 21 control voltage note 3 t de-emph =50 m s0 -- mv t de-emph =80 m s - 300 -- mv t de-emph control range of de-emphasis 50 - 80 m s voltage controlled oscillator; note 4 f osc oscillator frequency range 225 228 231 khz noise blanker i nterference detection fully internal from level detector t sup interference suppression time 40 50 -m s t rigger threshold control i 51 charge charge current (into +4 v) - 45 -m a i 51 discharge discharge current (from +8.5 v) -- 900 -m a t rigger sensitivity measurement with pulsed modulation of fm-if 2 ; see figs 19 and 20 v 37-35(p) trigger sensitivity for test signal 1 (peak value) v 38 = 2.52 v; note 5 -- 0.8 mv v 38 = 2.52 v; note 6 100 -- mv trigger sensitivity for test signal 2 (peak value) v 38 = 2.52 v; note 6 5.0 -- mv v 38 = 2.52 v; note 6 100 -- mv v 51 trigger threshold variation with frequency modulation of fm-if 2 and f mod = 15 khz (pin 51) v 37-35 = 100 mv; d f=0khz - 6.4 - v d v 51 v 37-35 = 100 mv; d f=75khz - 520 - mv i offset gate input offset current at pins 31 and 32 during suppression pulse duration - 20 50 na symbol parameter conditions min. typ. max. unit 1997 feb 12 16 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t notes to the stereo decoder characteristics 1. the following equations give the values for the carrier and harmonic suppression at the output: 2. the stereo decoder can be set to mono via the i 2 c-bus. pilot presence indication via the i 2 c-bus. 3. the nominal de-emphasis value can be changed to 75 m s with c 31 ; c 32 = 10 nf. 4. the vco is adjusted by means of a digital auxiliary pll. 5. noise blanker does not trigger. 6. noise blanker triggers. a 2 v 0 signal () (at1khz) v 0 spurious () (at 1 khz) ----------------------------------------------------------------- - = f s 2 10 khz () 19 khz C = a 3 v 0 signal () (at 1 khz) v 0 spurious () (at 1 khz) ----------------------------------------------------------------- - = f s 3 13 khz () 38 khz C = a 57 (ari) v 0 signal () (at 1 khz) v 0 spurious () at 1 khz 23 hz () ---------------------------------------------------------------------------------------------- - = a 67 v 0 signal () (at 1 khz) v 0 spurious () (at 9 khz) ----------------------------------------------------------------- - = f s 2 38 khz () 67 khz C = a 114 v 0 signal () (at 1 khz) v 0 spurious () (at 4 khz) ----------------------------------------------------------------- - = f s 110 khz 3 38 khz () C = a 190 v 0 signal () (at 1 khz) v 0 spurious () (at 4 khz) ----------------------------------------------------------------- - = f s 186 khz 5 38 khz () C = 1997 feb 12 17 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t characteristics for analog-to-digital converters (adcs) for level and multi-path voltages notes 1. the fm level information v 50-3 is analog-to-digital converted with 4 bits. 2. the am level information v 49-4 is analog-to-digital converted with 4 bits. 3. the multi-path information v 40-4 is analog-to-digital converted with 3 bits covering an if 2 amplitude modulation range m 0.6; f mod = 20 khz. symbol parameter conditions min. typ. max. unit adc for fm level information; note 1 d v 37-35 analog-to-digital conversion step size 2 4 8 db/step d v 37-35 analog-to-digital conversion level range 43 56 69 db fm stop d v stop variation of stop level as function of v 42-4 - 16 - db/v adc for am level information; note 2 d v 33-34 analog-to-digital conversion step size 2 4 8 db/step d v 33-34 analog-to-digital conversion level range 43 56 69 db am stop d v stop variation of stop level as function of v 43-4 - 16 - db/v adc for multi-path information; note 3 m multi-path conversion step 0 -- 5% step 1 - 15 - % step 2 - 22 - % step 3 - 28 - % step 4 - 34 - % step 5 - 40 - % step 6 - 46 - % step 7 - 52 60 % 1997 feb 12 18 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t fig.4 test circuit fm mixer. handbook, full pagewidth mha206 330 w generator r&s smpc r g = 50 w 1 : 1 f if1 = 72.2 mhz f if2 = 10.7 mhz 13 14 19 20 + 8.5 v 3.5 3.5 2 low noise amplifier avd 704201 (s/n = 103 db) spectrum analyzer hp8568a TEA6820T tea6822t fig.5 test circuit if-amplifier. handbook, full pagewidth mha207 330 w generator r&s smpc r g = 50 w passive attenuator ? db r in = 50 w r out = 330 w 27 24 29 4 oscilloscope pm3295a 10 nf 10 nf 10 nf TEA6820T tea6822t fig.6 test circuit limiter gain. handbook, full pagewidth mha208 50 w generator r&s smpc r g = 50 w 37 35 1 2 oscilloscope pm3295a TEA6820T tea6822t 10 nf 100 nf 10 nf 10 nf 1997 feb 12 19 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t handbook, full pagewidth 20 ?0 ?0 10 ? 10 ? 10 ? 1 10 10 2 (2) (1) 10 3 mha247 0 ?0 ?0 v 37-35 (mv) v 47-4 (db) fig.7 signal and noise of muted mpx voltage. (1) af: f if = 10.7 mhz; deviation = 22.5 khz; f mod = 1 khz. (2) noise: unweighted b = 250 hz to 15 khz with de-emphasis 50 m s. handbook, full pagewidth 20 ?0 ?0 10 ? 10 ? 10 ? 1 10 10 2 (2) (1) 10 3 mha248 0 ?0 ?0 v 37-35 (mv) v 43-4 (db) fig.8 signal and noise of unmuted mpx voltage. (1) af: f if = 10.7 mhz; deviation = 22.5 khz; f mod = 1 khz. (2) noise: unweighted b = 250 hz to 15 khz with de-emphasis 50 m s. 1997 feb 12 20 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t fig.9 unweighted voltage level (typical curve). (1) temperature compensation off. (2) temperature compensation on. handbook, full pagewidth 10 0 2 10 ? 10 ? 10 ? 1 10 10 2 (2) (1) 10 3 mha249 8 4 6 v 37-35 (mv) v 50-4 (v) fig.10 adjustment range of unweighted voltage level. handbook, full pagewidth 10 0 2 10 ? 10 ? 10 ? 1 10 10 2 10 3 mha250 8 4 6 v 37-35 (mv) v 50-4 (v) 1997 feb 12 21 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t handbook, full pagewidth 20 ?0 ?0 10 ? 10 ? 10 ? 1 10 10 2 (1) (4) (4) 10 3 mha251 0 ?0 ?0 v 37-35 (mv) v 47-4 (db) (3) (5) (2) (5) (3) fig.11 muting dependence of unweighted voltage level (typical curve). (1) af: f if = 10.7 mhz; deviation = 22.5 khz; f mod = 1 khz. (2) noise: unweighted b = 250 hz to 15 khz with de-emphasis 50 m s. (3) level adjustment set to a 3db at 0.6 mv. (4) level adjustment set to a 3db at 0.4 mv. (5) level adjustment set to a 3db at 1 mv. 1997 feb 12 22 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t fig.12 typical mute voltage as function of fm-if 2 voltage. handbook, full pagewidth 10 0 2 10 ? 10 ? 10 ? 1 10 10 2 10 3 mha252 8 4 6 v 37-35 (mv) v 49-4 (v) fig.13 adjustment range mute voltage. handbook, full pagewidth 10 0 2 10 ? 10 ? 10 ? 1 10 10 2 10 3 mha213 8 4 6 v 37-35 (mv) v 49-4 (v) 1997 feb 12 23 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t fig.14 test circuit am mixer. handbook, full pagewidth 270 w mha209 2.2 k w 27 24 22 23 + 8.5 v 7 7 20 low noise amplifier avd 704201 (s/n = 103 db) spectrum analyzer hp8568a generator r&s smpc r g = 50 w f if1 = 10.7 mhz 10 nf 22 nf 10 nf TEA6820T tea6822t handbook, full pagewidth 20 ?0 ?0 10 ? 10 ? 10 ? 11010 2 10 3 mha214 0 ?0 ?0 v 33-34 (mv) v 48-4 (db) 8 0 6 2 4 thd (%) (1) (2) (3) (4) fig.15 signal, noise and distortion of am af output voltage and am voltage level (typical curve). (1) af: f = 450 khz; m = 30%; f mod = 400 hz. (2) noise: unweighted b = 250 hz to 15 khz. (3) thd m = 80%. (4) am level voltage. 1997 feb 12 24 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t fig.16 adaption of mpx input to fm-demodulator output level by variation of the input resistor. handbook, full pagewidth 300 4 3 1 0 0 100 200 mha215 2 r in(pin20) (k w ) v i,mpx(p-p) (v) fig.17 channel separation as function of control voltage. handbook, full pagewidth 0 40 30 10 0 ?00 ?00 ?00 mha216 20 control voltage v 17 ?0.765v 21 (mv) a cs (db) 1997 feb 12 25 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t fig.18 high-cut with f mod = 10 khz as function of control voltage. handbook, full pagewidth 0 0 ? ? ? ?00 ?00 ?00 mha217 ? control voltage v 18 ?0.765v 21 (mv) (db) 1997 feb 12 26 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t fig.19 test signal 1 for interference detection from level detector. handbook, full pagewidth f if = 10.7 mhz t = 5 m s t r = t f = 0.5 m s t rep = 1 ms a v 37-35 t 0.6 a mha210 fig.20 test signal 2 for interference detection from level detector. handbook, full pagewidth t = 5 m s t r = t f = 0.5 m s t rep = 1 ms f if = 10.7 mhz a v 37-35 t 0.2 a mha211 1997 feb 12 27 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t i 2 c-bus and i 2 c-bus controlled functions i 2 c-bus speci?cation the standard i 2 c-bus specification is expanded by the following definitions. structure of the i 2 c-bus logic: slave transceiver with auto increment and expansion to switch a direct transfer of all transmissions to an output for the radio front-end ic (tea6810t respectively tea6811t). subaddresses are not used. d ata transfer for the TEA6820T and the tea6822t data sequence: address byte 1 byte 2. the data transfer maybe in this order only. the transfer direction of the data bytes is defined by the lsb of the address. the data becomes valid at the output of the internal latches with the acknowledge of each byte. a stop condition after any byte can shorten transmission times. when writing to the transceiver by using the stop condition before completion of the whole transfer: the remaining bytes will contain the old information if the transfer of a byte was not completed, this byte is lost and the previous information is available. d ata transfer to an output of the front - end ic a data bit in the transceiver of the TEA6820T or tea6822t enables or disables a direct transfer of all transmissions to an interface stage for the front-end ic. for a transmission to the front-end ic the address and the data format of the front-end ic has to be used. remark: the pull-up resistors for the front-end interface (pins 6 and 7) should not be connected to the 5 v supply voltage of the front-end ic, otherwise a bus pull-down (pin 53) can occur during switching off the front-end supply when the interface stage is enabled. d ata transfer to the if ic data transfer to the if ic (TEA6820T or tea6822t) is independent of the state of interface stage for the front-end ic. table 1 structure of the i 2 c-bus table 2 data to be received by the ic for data byte 1 table 3 reference frequency setting in data byte 1; see table 1 description specification bus address of the TEA6820T and the tea6822t 1100001x subaddress not used hardware (pin) programmable address bits not available default settings by power-on reset data byte 1 bits 4 to 7 are set to logic 0; all other bits are random bit description result 0 switch for mono bi t0=1 switch for stereo bi t0=0 1 lsb reference frequency for synthesizer 2 reference frequency for synthesizer 3 msb reference frequency for synthesizer 4 tuning mute off bi t4=1 tuning mute on bi t4=0 5 sds/sdr hold off bi t5=1 sds/sdr hold on bi t5=0 6 radio mute off bi t6=1 radio mute on bi t6=0 7i 2 c-bus to front-end enabled bi t7=1 i 2 c-bus to front-end disabled bi t7=0 bit 3 bit 2 bit 1 frequency setting 0 0 0 3 khz 0 0 1 5 khz 0 1 0 10 khz 0 1 1 15 khz 1 0 0 25 khz 1 0 1 50 khz 1 1 0 not de?ned 1 1 1 not de?ned 1997 feb 12 28 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t table 4 data to be received by the ic for data byte 2 table 5 data to be transmitted by the ic for data byte 1; note 1 note 1. the analog-to-digital conversion for multi-path and level will be done during a transmission of any address to the i 2 c-bus. bit description result 0 am/fm; am mode bi t0=0 am/fm; fm mode bi t0=1 1 divider for am mixer; divide by 2 bi t1=0 divider for am mixer; divide by 6 bi t1=1 2 measure time if-count; 40 ms bi t2=0 measure time if-count; 4 ms bi t2=1 3 sdr off bi t3=0 sdr on bi t3=1 4 if-prescaler division rate; divide by 200 bit4=0 if-prescaler division rate; divide by 25 bit4=1 5 sensitivity unchanged bi t5=0 multi-path sensitivity switch; less sensitivity by an offset of d m = 10% bit5=1 6 temperature compensation of unweighted voltage level; temperature coef?cient as speci?ed in chapter characteristics temperature compensation off bi t6=0 temperature compensation on bi t6=1 7 not used bit description 0 bit 1 level information 1 bit 2 level information 2 msb (bit 3) level information 3 lsb multi-path information 4 multi-path information 5 msb multi-path information 6 stereo pilot presence; bit 6 = 1 7 lsb (bit 0) level information table 6 data to be transmitted by the ic for data byte 2 r eferenced frequency generation table 7 division ratios note 1. all specified frequencies are valid for a crystal oscillator frequency of 61.5 mhz. bit description 0 lsb of the if-counter 1 if-counter 2 if-counter 3 if-counter 4 if-counter 5 if-counter 6 if-counter 7 msb of the if-counter division ratio reference frequency (khz) (1) 20500 3 12300 5 6150 10 4100 15 2460 25 1230 50 1997 feb 12 29 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t table 8 output signal of reference frequency divider if counter table 9 if counter sensitivity am counting windows are 4 or 40 ms. fm counting windows are 4 or 40 ms. am counting resolution is 250 or 25 hz. fm counting resolution is 5 khz, 625 hz, 50 khz or 6.25 khz. am if-prescaler is divisible by 1. fm if-prescaler is divisible by 25 or 200. symbol parameter min. typ. max. unit v 10-11(p-p) differential output voltage (peak-to-peak value) 0.3 0.4 0.5 v v 10-4(p-p) ; v 11-4(p-p) single-ended output voltage (peak-to-peak value) 0.15 0.2 0.3 v c 10-4 ; c 11-4 output capacitance -- 4pf r 10-52 ; r 11-52 output resistance 800 1000 1200 w symbol parameter conditions min. unit v 33-34 if counter sensitivity am mode; m = 0 200 m v v 37-35 if counter sensitivity fm mode 200 m v fig.21 if counter structure. handbook, full pagewidth mha205 fm if2 am if2 prescaler setting fm if-prescaler ? 25 / ? 200 8-bit binary counter 4 ms/40 ms counter window b0 b1 b2 b3 b4 b5 b6 b7 1997 feb 12 30 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t if counter read out if counter read out as a function of fm or am position, counter window and prescaler setting note 1. in position fm with a prescaler ratio of 25, counter window of 40 ms and in position am with 40 ms counter window ambiguous counting results within the if filter bandwidth are obtained. the counting range is 127 counts above and 127 counts below the nominal if of 10.7 mhz for fm and 450 khz for am. the if count windows are valid for a crystal oscillator frequency of 61.5 mhz. the fm/am switching is carried out by bit 0 of byte 2 of the received data of the ic. the if counter operates continuously. the if counter and window-counter will be reset when the i 2 c-bus logic detects the address of the ic. this disables changes in the latches for the if count, while reading this value. if the transmission to the front-end ic is disabled after the synthesizer loop of the tea6810t/tea6811t front-end ic has locked for a new frequency, the if-count will be available after the set measuring time. the if counter starts at 0. the if counter output are the 8 least significant bits of the counting result. fm/am prescaler ratio window (ms) f if (khz) read out resolution (hz/count) range (khz) min. max. fm 200 4 10700 d6h 50000 4300 17050 fm 200 40 10700 5ch 5000 10065 11335 fm 25 4 10700 b0h 6250 9906.25 11493.75 fm (1) 25 40 10700 e0h 625 10620.63 10779.38 am 1 4 450 08h 250 418.25 481.75 am (1) 1 40 450 50h 25 446.83 453.18 1997 feb 12 31 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t internal circuitry table 10 equivalent pin circuits and pin voltages pin symbol dc voltage (v) equivalent circuit am fm 1 qdet1 4.0 4.0 2 qdet2 4.0 4.0 3 tswitch open 0.4 to 0.6 4 agnd -- 5v dda1 5.0 5.0 6 hfbus1 5.0 5.0 7 hfbus2 5.0 5.0 mha164 39 1 2 mha165 3 mha166 6 mha167 7 1997 feb 12 32 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t 8 xtal1 4.1 4.1 9 xtal2 4.1 4.1 10 f ref(p) 4.9 4.9 11 f ref(n) 4.9 4.9 12 i ref 4.3 4.3 13 fmif1in1 2.3 2.3 14 fmif1in2 2.3 2.3 pin symbol dc voltage (v) equivalent circuit am fm mha168 8 9 mha169 11 10 mha170 12 mha171 13 20 19 14 1997 feb 12 33 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t 15 tsdr 0.7 to 5.5 0.7 to 5.5 16 tsds 0.7 to 5.5 0.7 to 5.5 17 v sds 3.0 to 5.5 3.0 to 5.5 18 v sdr 3.0 to 5.5 3.0 to 5.5 19 fmif2out1 8.5 8.5 20 fmif2out2 8.5 8.5 pin symbol dc voltage (v) equivalent circuit am fm mha172 15 mha173 16 17 mha174 18 mha175 mha171 13 20 19 14 1997 feb 12 34 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t 21 v ref 5.1 5.1 22 amif2out1 8.5 8.5 23 amif2out2 8.5 8.5 24 fmamdec 3.0 2.5 25 phasedet 2.8 to 7.0 2.8 to 7.2 26 pildet 0.4 0.4 to 7.0 pin symbol dc voltage (v) equivalent circuit am fm mha176 21 mha177 23 22 mha178 24 mha179 25 mha180 26 1997 feb 12 35 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t 27 fmam10.7 3.0 2.5 28 v dda2 8.5 8.5 29 fmifampout 6.0 6.0 30 afgnd 3.6 3.6 31 deemphr 2.3 2.3 32 deemphl 2.3 2.3 pin symbol dc voltage (v) equivalent circuit am fm 27 mha181 29 mha182 30 mha183 31 mha184 32 mha185 1997 feb 12 36 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t 33 amif2in1 2.7 0.7 34 amif2in2 2.7 0.7 35 fmin2 0.7 2.7 36 dcfeed 2.7 2.7 37 fmin1 0.7 2.7 38 leveladj 2.6 2.6 pin symbol dc voltage (v) equivalent circuit am fm 34 33 mha186 35 mha187 mha188 37 36 38 mha189 1997 feb 12 37 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t 39 c afc 1.0 to 2.2 1.0 to 7.0 40 mpbuf 0.7 to 6.0 0.7 to 6.0 41 outleft 3.6 3.6 42 fmstop 0 to 5.2 0 to 5.2 43 rds/amstop 0 to 5.2 3.0 44 outright 3.6 3.6 pin symbol dc voltage (v) equivalent circuit am fm mha164 39 1 2 40 mha190 41 mha191 42 mha192 43 mha193 44 mha194 1997 feb 12 38 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t 45 mpxin 2.8 2.8 46 i.c. -- 47 mpxout 0 3.0 48 amafout 3.7 4.8 49 v mute/aml 1.0 to 5.5 1.0 to 5.5 50 levelunweig 1.0 to 7.0 1.0 to 7.0 51 iac contr 0 6.0 52 v ddd 5.0 5.0 pin symbol dc voltage (v) equivalent circuit am fm 45 mha195 47 mha197 mha198 48 49 mha199 50 mha200 51 mha201 1997 feb 12 39 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t 53 sda 5.0 5.0 54 scl 5.0 5.0 55 dgnd 0 0 56 v dda3 8.5 8.5 pin symbol dc voltage (v) equivalent circuit am fm mha202 53 mha203 54 1997 feb 12 40 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t application information fig.22 ice application diagram (continued in fig.23). time constant control: slow or fast attack and decay time constants for soft mute, mono/stereo and high-cut control can be chosen by connecting pin 3 to gnd or pin 21. handbook, full pagewidth 22 nf 100 nf 27 w 390 w 2.7 k w 330 w 68 w v cc1 330 w 100 nf 100 nf 10 k w 100 nf 47 m f 11 sfe10.7 sfe10.7 sfe 10.7 22 w 61.5 mhz scl sda 40 220 nf 1.5 nf 82 k w 100 k w leveladj 29 14 :2/:6 54 v ref 100 100 nf sfp450 100 k w 9 6 53 7 10 13 20 24 27 33 28 8 42 38 37 36 35 34 55 19 fmstop 22 23 if- multi- adc i 2 c-bus counter buffer 20 khz level adc amplifier level :n5 am-amplifier fm-limiter switch am/fm reference oscillator fm am bf840 10 nf 56 pf 56 pf 2 zs369scs- 2144aj 7psag- 1946d = s philips 9922 521 00098 or daiwa at - 49 level detector if- frequency amplifier path 22 nf 22 w 100 m f 220 k w 22 w 47 pf bb135 100 nf 12 nf 100 pf 33 m f 470 w 100 nf 10 nf 270 pf 10 pf 220 w 100 nf 100 w buffer 68 m h bf861a 2.7 pf 32 drive diode pin 1 m f 14 12 10 k w 19 16 15 21 gap band- 1 mh 18 11 :n2 limiter am/fm 13 100 nf buffer 1 6 7 2 9 4 5 8 am/fm am/fm am/fm 3 10 17 20 v cc 40 39 3.3 nf 10 k w 36 35 37 38 34 30 31 33 100 pf 330 nh 47 mh 29 28 27 25 26 26 22 8.2 pf 1.8 pf 22 pf 10 nf 470 w 47 w 100 nf agc rf am - divider programable oscillator am/fm pump agc fm detector lock am detector phase bus tea6810t tea6811t charge 1 m f 1 m f 47 m f 220 m h 3.6 k w 2.2 k w 388bn-1211z e543snas -02010 10 pf 10 pf 1 nf 47 k w v ccan nf in-lock 3.3 m h am/fm 1.8 pf 4 to 10 pf bb804 47 k w 10 m f 1 nf 5.6 pf 6.8 pf 6.8 m h 3.3 m h 220 nf 270 pf 33 m h e543snas -04011 bav 99 isv 172 2.2 m w +8.5 v v cc +8.5 v +8.5 v v ccd +5 v +5 v v cc +8.5 v l7 l1 tr2 tr3 tr4 tr5 r39 r40 control TEA6820T tea6822t mha254 e f g h a b c d 1 k w 330 pf 330 pf 10 k w sda scl 10 k w 330 w 330 w p392be- 2049aj = s 1997 feb 12 41 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t fig.23 ice application diagram (continued from fig.22). handbook, full pagewidth 100 nf 100 nf 39 43 48 100 k w 33 k w 33 k w amstop 10 nf rds v ref 220 k w 68 pf 220 nf 100 nf 2.2 m w 820 k w 12 k w 33 k w 1.2 m w p392bc-1977z toko 220 nf 82 k w 100 nf 470 nf v int2 v int1 31 100 nf 15 100 k w 3.3 nf 62 pf 4.3 k w 17 18 detector noise former pulse detector interference - + 1 m w 27 k w 22 nf 220 nf 3.3 m w mute radio mute radio tuning mute mute soft 30 am 3 2 1 outleft 16 21 25 26 51 50 49 47 46 45 44 detector average detector peak detector peak detector average switch current 60 khz pass high afc pass high mono matrix and decoder mpx- 38 khz 19 khz block logic canceller pilot f ref detector pilot detector phase digital vco detector phase filter low mpx delog am supply 56 32 41 52 outright 12 5 4 100 nf 120 k w 100 nf 470 nf 33 m f 10 w 68 m f 6.8 nf 6.8 nf level buffer v ref i.c. - + - + amplifier pass filter l13 r51 r41 v int1 v int2 temperature compensation TEA6820T tea6822t h g f e d c b a mha255 47 m f 47 m f v ccan v ccdig 22 m h v cc + 8.5 v + 8.5 v +5 v +5 v 1997 feb 12 42 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t handbook, full pagewidth 220 w 220 m h 22 nf 220 k w 22 k w 1 m f 1 m f 47 pf bb135 100 nf 3.6 k w 100 pf 330 pf 330 pf 56 pf 10 nf 56 pf 100 nf 22 nf 1.5 nf 100 k w 82 k w 100 k w 220 k w 10 nf 220 nf 82 k w 68 pf 220 nf 100 nf 100 nf 12 k w 33 k w 1.2 m w 2.2 m w 820 k w 22 nf 2.7 k w 470 nf 100 pf 330 nh 100 nf 1 mh bf861a fmstop outleft outright v ref scl sda detector lock sfe10.7 sfe10.7 270 pf 100 nf 100 nf 1 m w 3.3 m w 100 nf 120 k w 1 k w 470 nf 61.5 mhz 100 nf 47 m f 47 m f 22 m h 100 nf 27 k w 220 nf sfp450 100 k w 3.3 nf 220 nf 100 k w 33 k w 33 k w v ref 4.3 k w 62 pf 100 nf 47 m f 100 nf sfe10.7 100 nf 100 nf 56 50 45 40 35 30 29 28 25 20 15 10 5 1 2.2 k w 20 15 10 5 1 35 30 25 21 40 100 nf 10 nf 12 nf 10 pf 8.2 pf 1 m f 1.8 pf 2.7 pf 3.3 nf 10 k w 100 nf 22 pf 68 m h 33 m f 470 w 100 w 33 m f +5 v 10 k w 6.8 nf 6.8 nf 330 w 390 w 27 w 330 w 68 m f +8.5 v +8.5 v 10 k w 10 k w 100 nf 470 w 22 w 100 m f 47 mh bav 99 +5 v +8.5 v f ref +5 v rdsmpx amstop sep level v ccan v ccdig v cc v ccdig v cc tea6810t tea6811t TEA6820T tea6822t leveladj sda 7psag-1946d = s p392be- s369scs-2144aj (2x) p392bc-1977z e543snas-02010 bf840 100 nf scl 6.8 m h 388bn-1211z 3.3 m h 33 m h 270 pf 10 pf 1 nf 10 pf 10 pf 5.6 pf 6.8 pf 47 k 47 w w isv172 1 nf 47 k w 2.2 m w 10 k w 1.8 pf 4 to 10 pf bb 804 e543snas -4011 2049aj = s l7 l1 l13 tr2 tr3 tr4 tr5 330 w 330 w r41 r39 r51 r40 220 nf mha256 fig.24 am/fm car radio receiver with tea6810t and TEA6820T or tea6811t and tea6822t. 1997 feb 12 43 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t package outlines unit a 1 a 2 a 3 b p cd (1) e (2) (1) eh e ll p qz y w v q references outline version european projection issue date iec jedec eiaj mm inches 0.3 0.1 3.0 2.8 0.25 0.42 0.30 0.22 0.14 21.65 21.35 11.1 11.0 0.75 15.8 15.2 1.45 1.30 0.90 0.55 7 0 o o 0.1 0.1 dimensions (inch dimensions are derived from the original mm dimensions) 1.6 1.4 sot190-1 92-11-17 96-04-02 w m q a a 1 a 2 b p d h e l p q detail x e z e c l v m a x (a ) 3 a y 56 29 28 1 pin 1 index 0.012 0.004 0.12 0.11 0.017 0.012 0.0087 0.0055 0.85 0.84 0.44 0.43 0.03 2.25 0.089 0.62 0.60 0.057 0.051 0.035 0.022 0.004 0.2 0.008 0.004 0.063 0.055 0.01 0 5 10 mm scale vso56: plastic very small outline package; 56 leads sot190-1 a max. 3.3 0.13 note 1. plastic or metal protrusions of 0.3 mm maximum per side are not included. 2. plastic interlead protrusions of 0.25 mm maximum per side are not included. 1997 feb 12 44 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t unit a 1 a 2 a 3 b p cd (1) e (2) (1) eh e ll p qz y w v q references outline version european projection issue date iec jedec eiaj mm inches 0.3 0.1 3.0 2.8 0.25 0.42 0.30 0.22 0.14 21.65 21.35 11.1 11.0 0.75 15.8 15.2 1.45 1.30 0.90 0.55 7 0 o o 0.1 0.1 dimensions (inch dimensions are derived from the original mm dimensions) 1.6 1.4 sot190-2 95-04-26 96-04-02 w m b p d h e e z e c v m a x a y q a a 1 a 2 l p q detail x l (a ) 3 56 29 28 1 pin 1 index 0.012 0.004 0.12 0.11 0.017 0.012 0.0087 0.0055 0.85 0.84 0.44 0.43 0.03 2.25 0.089 0.62 0.60 0.057 0.051 0.035 0.022 0.004 0.2 0.008 0.004 0.063 0.055 0.01 0 5 10 mm scale vso56: plastic very small outline package; 56 leads; face down sot190-2 a max. 3.3 0.13 note 1. plastic or metal protrusions of 0.3 mm maximum per side are not included. 2. plastic interlead protrusions of 0.25 mm maximum per side are not included. 1997 feb 12 45 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t soldering introduction there is no soldering method that is ideal for all ic packages. wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. however, wave soldering is not always suitable for surface mounted ics, or for printed-circuits with high population densities. in these situations reflow soldering is often used. this text gives a very brief insight to a complex technology. a more in-depth account of soldering ics can be found in our ic package databook (order code 9398 652 90011). re?ow soldering reflow soldering techniques are suitable for all vso packages. reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. several techniques exist for reflowing; for example, thermal conduction by heated belt. dwell times vary between 50 and 300 seconds depending on heating method. typical reflow temperatures range from 215 to 250 c. preheating is necessary to dry the paste and evaporate the binding agent. preheating duration: 45 minutes at 45 c. wave soldering wave soldering techniques can be used for all vso packages if the following conditions are observed: a double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used. the longitudinal axis of the package footprint must be parallel to the solder flow. the package footprint must incorporate solder thieves at the downstream end. during placement and before soldering, the package must be fixed with a droplet of adhesive. the adhesive can be applied by screen printing, pin transfer or syringe dispensing. the package can be soldered after the adhesive is cured. maximum permissible solder temperature is 260 c, and maximum duration of package immersion in solder is 10 seconds, if cooled to less than 150 c within 6 seconds. typical dwell time is 4 seconds at 250 c. a mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. repairing soldered joints fix the component by first soldering two diagonally- opposite end leads. use only a low voltage soldering iron (less than 24 v) applied to the flat part of the lead. contact time must be limited to 10 seconds at up to 300 c. when using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 c. 1997 feb 12 46 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t definitions life support applications these products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify philips for any damages resulting from such improper use or sale purchase of philips i 2 c components data sheet status objective speci?cation this data sheet contains target or goal speci?cations for product development. preliminary speci?cation this data sheet contains preliminary data; supplementary data may be published later. product speci?cation this data sheet contains ?nal product speci?cations. limiting values limiting values given are in accordance with the absolute maximum rating system (iec 134). stress above one or more of the limiting values may cause permanent damage to the device. these are stress ratings only and operation of the device at these or at any other conditions above those given in the characteristics sections of the speci?cation is not implied. exposure to limiting values for extended periods may affect device reliability. application information where application information is given, it is advisory and does not form part of the speci?cation. purchase of philips i 2 c components conveys a license under the philips i 2 c patent to use the components in the i 2 c system provided the system conforms to the i 2 c specification defined by philips. this specification can be ordered using the code 9398 393 40011. 1997 feb 12 47 philips semiconductors preliminary speci?cation in car entertainment (ice) car radio TEA6820T; tea6822t notes internet: http://www.semiconductors.philips.com philips semiconductors C a worldwide company ? philips electronics n.v. 1997 sca53 all rights are reserved. reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. the information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. no liability will be accepted by the publisher for any consequence of its use. publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. netherlands: postbus 90050, 5600 pb eindhoven, bldg. vb, tel. +31 40 27 82785, fax. +31 40 27 88399 new zealand: 2 wagener place, c.p.o. box 1041, auckland, tel. +64 9 849 4160, fax. +64 9 849 7811 norway: box 1, manglerud 0612, oslo, tel. +47 22 74 8000, fax. +47 22 74 8341 philippines: philips semiconductors philippines inc., 106 valero st. salcedo village, p.o. box 2108 mcc, makati, metro manila, tel. +63 2 816 6380, fax. +63 2 817 3474 poland: ul. lukiska 10, pl 04-123 warszawa, tel. +48 22 612 2831, fax. +48 22 612 2327 portugal: see spain romania: see italy russia: philips russia, ul. usatcheva 35a, 119048 moscow, tel. +7 095 755 6918, fax. +7 095 755 6919 singapore: lorong 1, toa payoh, singapore 1231, tel. +65 350 2538, fax. +65 251 6500 slovakia: see austria slovenia: see italy south africa: s.a. philips pty ltd., 195-215 main road martindale, 2092 johannesburg, p.o. box 7430 johannesburg 2000, tel. +27 11 470 5911, fax. +27 11 470 5494 south america: rua do rocio 220, 5th floor, suite 51, 04552-903 s?o paulo, s?o paulo - sp, brazil, tel. +55 11 821 2333, fax. +55 11 829 1849 spain: balmes 22, 08007 barcelona, tel. +34 3 301 6312, fax. +34 3 301 4107 sweden: kottbygatan 7, akalla, s-16485 stockholm, tel. +46 8 632 2000, fax. +46 8 632 2745 switzerland: allmendstrasse 140, ch-8027 zrich, tel. +41 1 488 2686, fax. +41 1 481 7730 taiwan: philips semiconductors, 6f, no. 96, chien kuo n. rd., sec. 1, taipei, taiwan tel. +886 2 2134 2870, fax. +886 2 2134 2874 thailand: philips electronics (thailand) ltd., 209/2 sanpavuth-bangna road prakanong, bangkok 10260, tel. +66 2 745 4090, fax. +66 2 398 0793 turkey: talatpasa cad. no. 5, 80640 gltepe/istanbul, tel. +90 212 279 2770, fax. +90 212 282 6707 ukraine : philips ukraine, 4 patrice lumumba str., building b, floor 7, 252042 kiev, tel. +380 44 264 2776, fax. +380 44 268 0461 united kingdom: philips semiconductors ltd., 276 bath road, hayes, middlesex ub3 5bx, tel. +44 181 730 5000, fax. +44 181 754 8421 united states: 811 east arques avenue, sunnyvale, ca 94088-3409, tel. +1 800 234 7381 uruguay: see south america vietnam: see singapore yugoslavia: philips, trg n. pasica 5/v, 11000 beograd, tel. +381 11 625 344, fax.+381 11 635 777 for all other countries apply to: philips semiconductors, marketing & sales communications, building be-p, p.o. box 218, 5600 md eindhoven, the netherlands, fax. +31 40 27 24825 argentina: see south america australia: 34 waterloo road, north ryde, nsw 2113, tel. +61 2 9805 4455, fax. +61 2 9805 4466 austria: computerstr. 6, a-1101 wien, p.o. box 213, tel. +43 1 60 101, fax. +43 1 60 101 1210 belarus: hotel minsk business center, bld. 3, r. 1211, volodarski str. 6, 220050 minsk, tel. +375 172 200 733, fax. +375 172 200 773 belgium: see the netherlands brazil: see south america bulgaria: philips bulgaria ltd., energoproject, 15th floor, 51 james bourchier blvd., 1407 sofia, tel. +359 2 689 211, fax. +359 2 689 102 canada: philips semiconductors/components, tel. +1 800 234 7381 china/hong kong: 501 hong kong industrial technology centre, 72 tat chee avenue, kowloon tong, hong kong, tel. +852 2319 7888, fax. +852 2319 7700 colombia: see south america czech republic: see austria denmark: prags boulevard 80, pb 1919, dk-2300 copenhagen s, tel. +45 32 88 2636, fax. +45 31 57 1949 finland: sinikalliontie 3, fin-02630 espoo, tel. +358 9 615800, fax. +358 9 61580/xxx france: 4 rue du port-aux-vins, bp317, 92156 suresnes cedex, tel. +33 1 40 99 6161, fax. +33 1 40 99 6427 germany: hammerbrookstra?e 69, d-20097 hamburg, tel. +49 40 23 53 60, fax. +49 40 23 536 300 greece: no. 15, 25th march street, gr 17778 tavros/athens, tel. +30 1 4894 339/239, fax. +30 1 4814 240 hungary: see austria india: philips india ltd, shivsagar estate, a block, dr. annie besant rd. worli, mumbai 400 018, tel. +91 22 4938 541, fax. +91 22 4938 722 indonesia: see singapore ireland: newstead, clonskeagh, dublin 14, tel. +353 1 7640 000, fax. +353 1 7640 200 israel: rapac electronics, 7 kehilat saloniki st, tel aviv 61180, tel. +972 3 645 0444, fax. +972 3 649 1007 italy: philips semiconductors, piazza iv novembre 3, 20124 milano, tel. +39 2 6752 2531, fax. +39 2 6752 2557 japan: philips bldg 13-37, kohnan 2-chome, minato-ku, tokyo 108, tel. +81 3 3740 5130, fax. +81 3 3740 5077 korea: philips house, 260-199 itaewon-dong, yongsan-ku, seoul, tel. +82 2 709 1412, fax. +82 2 709 1415 malaysia: no. 76 jalan universiti, 46200 petaling jaya, selangor, tel. +60 3 750 5214, fax. +60 3 757 4880 mexico: 5900 gateway east, suite 200, el paso, texas 79905, tel. +9-5 800 234 7381 middle east: see italy printed in the netherlands 547027/1200/03/pp48 date of release: 1997 feb 12 document order number: 9397 750 01395 |
Price & Availability of TEA6820T
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |